For USA

Supplier’s Declaration of Conformity

This Declaration of Conformity is hereby issued according to Chapter 1, Subpart A, Part 2 of Title 47 of the Code of Federal Regulations by:

Fourth Frontier Technologies Private Limited

2nd & 3rd Floor, No. 794, 12th Main, 1st Cross,

HAL 2nd Stage, Indiranagar, Bengaluru - 560038, Karnataka, India

RESPONSIBLE PARTY located in the United States:

Fourth Frontier Technologies, LLC

11824 Jollyville road, Suite 102

Austin TX 78759, USA

info@fourthfrontier.com

The responsible party warrants that each unit of equipment marketed under this Declaration of Conformity will be identical to the unit tested and found acceptable with the standards and that the records maintained by the responsible party continue to reflect the equipment being produced under such Supplier’s Declaration of Conformity continue to comply within the variation that can be expected due to quantity production and testing on a statistical basis.

"Product “Frontier X” complies with the applicable requirements of FCC Rule Part 15

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Contains FCC ID: 2ADHKATWINC1510

Contains FCC ID: 2ADHKBTZ

Product “Frontier X2” complies with the applicable requirements of FCC Rule Part 15

Contains FCC ID: QOQ-BGM220S2

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help

For Canada

This device complies with Industry Canada’s licence exempt RSS standards.

Contains IC:  5123A-BGM220S2

This device complies with Industry Canada’s license exempt RSS standard(s). Operation is subject to the following two conditions:(1) This device may not cause interference, and(2) This device must accept any interference, including interference that may cause undesired operation of the device.

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes:1.L’appareil ne doit pas produire de brouillage, et 2. L’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.

For Europe (EU)

CE marking :

This product is in compliance with the essential requirements and other relevant provisions of the following Directives – 2014/53/EU (RED), 2014/30/EU (EMC), 2011/65/EU (ROHS).  

The EU Declaration of Conformity (DoC) is provided below

• Download the CE Declaration of Conformity for Frontier X2

Disposal Information

This product shall be disposed of separately from household waste, in accordance with local laws and regulations. It shall be disposed of at a collection point designated by local authorities.

Battery

Charging Procedure:

• Charge your Frontier X2 in a dry and well-ventilated environment.
  
• Before charging, make sure the charging port is dry. Wipe off any water or sweat stains from the outside of the device and shake the device dry. Most importantly, ensure that the inside of the micro-USB port is absolutely dry. Failure to do so, might cause issues such as slow charging or overheating.
  
• The Frontier X2 does not come with a USB wall charger. Use a USB wall charger with a rated output voltage of 5 V and a rated output current not higher than 0.5 A.
• Plug one end of the USB cable into the wall charger and the other end of the cable into the micro-USB port on the side of the Frontier X2 device.
  
• During charging, a solid red LED will glow on the side of the device.
  
• Charging the device from 0 to 100% will typically take 1 hour, and in certain situations where the battery is fully discharged, expect longer charging times.
  
• Attention: Other chargers and power banks that do not meet corresponding safety standards may cause issues such as slow charging and overheating.

Expected Battery Life:

• A fully charged Frontier X2 can last ~ 24 hours in Monitor Mode, before you need to download your data and charge the device.
  
• Your fully charged Frontier X2 should last 14 days if used for an average of 1 hr/day.
  
• For optimal usage, we recommend charging your Frontier X when the battery level goes below 20%.

Viewing the Battery Level:

• When looking at the mobile app, your Frontier X2’s battery level appears in the top right of any screen.
  
• When you press the red button on the Frontier X2 once, the fourth screen will show you the battery level on the left, and the total memory consumption of the device on the right.

RF Exposure

Frontier X2 meets applicable limits for radio frequency (RF) exposure in different modes of operation, provided the following guidelines are followed.